Smoke alarms in Brisbane: plan, order and fit before 2027
If you need smoke alarms in Brisbane for a house, townhouse or unit, this page walks you through it in order: work out how many you need, choose the right type, order them, and have them up and tested before Queensland’s 1 January 2027 date. Greater Brisbane is where most of our orders go, so these are the questions we answer most.
Super Cheap Smoke Alarms sells interconnected photoelectric alarms from RED Smoke Alarms and Emerald Alarms, and posts them to Brisbane addresses by Australia Post. Questions are welcome on (07) 3155 5017 or through the contact page.

The rule for smoke alarms in Brisbane, in one paragraph
Brisbane follows the same law as the rest of the state. The Queensland Government says that by 1 January 2027, all existing private homes, townhouses, units and manufactured homes must have interconnected photoelectric smoke alarms. Each alarm must be photoelectric, must have no ionisation sensor, must comply with AS 3786:2014 (it’s marked on the alarm), and must be linked so they all sound together. Our 2027 deadline explainer goes into the detail, and the Queensland Government page is the official word.
Planning smoke alarms in Brisbane houses, townhouses and units
Planning starts with the Queensland Fire Department (QFD) placement list. Alarms must go in every bedroom, in every hallway or room that connects bedrooms, and on every storey of the home. Everything else follows from your floor plan.
Houses. Count each bedroom, then each hallway or room you pass through to get between bedrooms. If the house has more than one level, check that every storey has at least one alarm, even a storey with no bedrooms on it.
Townhouses. Many townhouses spread over two or three levels, with living areas below and bedrooms above. Treat each level as a storey that needs covering, and count the upstairs bedrooms and landing as you would in a house.
Units. A unit on one level is usually the simplest count: the bedrooms plus the hallway between them. If your unit is split over two levels, count it like a townhouse.
How many smoke alarms in Brisbane homes: three worked counts
These examples show the method. They are not a placement plan for your home; layouts vary, and QFD’s fact sheet is the guide.
- Two-bedroom unit, one level, bedrooms off a short hallway: 2 bedrooms + 1 hallway = 3 alarms.
- Three-bedroom townhouse on two levels, bedrooms upstairs off a landing, living areas downstairs: 3 bedrooms + 1 upstairs landing + 1 for the ground-floor storey = 5 alarms.
- Four-bedroom single-level house, bedrooms in two separate wings, each wing with its own hallway: 4 bedrooms + 2 hallways = 6 alarms.
Once you have your number, match it to a pack size in the shop. Our multi-packs include free remote controllers and magnetic mounting plates. If your count falls between pack sizes, ring us and we’ll talk it through.
Wireless or hardwired?
Look up at your current alarms before you order. QFD says that if your existing alarms are hardwired to mains power, the replacements must also be hardwired, and hardwired alarms must be installed by a qualified electrician.
If your current alarms run on batteries, or the home has none, wireless alarms are the straightforward option. QFD describes them as having a non-removable 10-year battery, connecting without wiring, and being something you can install yourself. RED’s R10RF and R10RFP and Emerald’s EVO10RF are our wireless models; RED’s R240RC is the 240V option for hardwired homes.
Brisbane rentals: who looks after the alarms
A lot of Brisbane homes are rented, and the Residential Tenancies Authority (RTA) sets out who does what. The owner or property manager must test the alarms within 30 days before a tenancy starts or is renewed, and replace any flat or nearly flat batteries.
The tenant must test and clean the alarms at least once every 12 months, replace flat batteries during the tenancy, and tell the owner or manager about any problem. Neither side may remove an alarm or do anything that makes it less effective, such as painting or covering it.
If you manage several Brisbane properties, it helps to keep a simple list of each address, its alarm count, the alarm type and the date code on each alarm. Our landlord guide covers the owner’s side in more depth.
A timeline that gets you there before 1 January 2027
Working backwards from the date makes the job manageable.
- Check what you have. Press the test button on one alarm and listen: do the others sound too? Look for AS 3786:2014 on the label and the date code. QFD says to replace alarms that contain an ionisation sensor, aren’t interconnected, or are more than 10 years old.
- Count and choose. Use the placement list above, then pick wireless or hardwired based on what’s on the ceiling now.
- Order. Standard Australia Post delivery to Brisbane takes 4 to 7 business days ($14.95, free on orders of $200 and over). Express takes 1 to 3 business days ($19.95).
- Fit and link. Follow the maker’s instructions to mount the alarms and link them. Book an electrician early if your home is hardwired.
- Test the whole set. Press test on each alarm in turn and check that every alarm in the home sounds.
Ordering smoke alarms in Brisbane: what to expect
All our prices include GST, and you can pay by card, PayPal, Klarna or Link at checkout. Every alarm is covered by the manufacturer’s warranty: 10 years from the date code on RED alarms, and up to 10 years from the date code on Emerald alarms.
If you’d like a closer look at a range before you buy, the RED Professional range and the Emerald range each have their own page. We also cover the Gold Coast and Sunshine Coast, and our service areas page lists the rest.
Frequently asked questions
Is the Brisbane deadline different from the rest of Queensland?
No. The 1 January 2027 date applies to existing private homes, townhouses, units and manufactured homes across Queensland.
Do I need an alarm on a storey with no bedrooms?
Yes. QFD says alarms must be installed on every storey of the home, as well as in bedrooms and in hallways or rooms connecting bedrooms.
My alarms are less than 10 years old. Can I keep them?
Only if they meet the rule: photoelectric, no ionisation sensor, AS 3786:2014 and interconnected. If any one of those is missing, they need replacing.
Can I paint the alarms to match a freshly painted ceiling?
No. QFD says never to paint over smoke alarms, and the RTA says neither an owner nor a tenant may do anything that makes an alarm less effective, such as painting or covering it. Mask the alarms off, or take wireless ones down while you paint and put them straight back up.
How quickly can alarms reach me in Brisbane?
Express post is 1 to 3 business days; standard is 4 to 7 business days.
This page is general information, not legal advice.
Sources
- Queensland Government, “Smoke alarms”: https://www.qld.gov.au/emergency/safety/fire/smoke-alarms (page last updated 29 Oct 2026; checked 2 Nov 2026)
- Queensland Fire Department, “Smoke alarm laws are changing in Queensland” fact sheet (QFE00206, 05/26): https://www.fire.qld.gov.au/sites/default/files/2026-06/Smoke-Alarm-Fact-Sheet.pdf (checked 2 Nov 2026)
- Residential Tenancies Authority, “Smoke alarm laws: what you need to know in Queensland”: https://www.rta.qld.gov.au/news/2020/08/12/smoke-alarm-laws-what-you-need-to-know-in-queensland (checked 27 Oct 2026)
- Manufacturer warranties: redsmokealarms.com.au/warranty and emeraldalarms.com.au/warranty (checked 2 Nov 2026)
Questions about smoke alarms in Brisbane?
Not sure which alarms suit your home, or how many you need? Tell us about your place through the contact page or call (07) 3155 5017, and we’ll help you choose. Browse the smoke alarm shop for wireless and hardwired alarms, delivered anywhere in Australia.
